Short answer: In a multi-operator or club contest, the log is built by several people, and the weak points are the moments when one operator leaves the chair and the next sits down. A short, fixed handover routine protects the log: say what the station is doing, check the logger settings and the clock, confirm the exchange you send, hand over the notes and keep the frequency while the new operator settles in. Two minutes at each change prevent lost QSOs, wrong exchanges and confusion in the final log.
Why the handover is a risk point
At a single-operator station, one person knows everything: which band is in use, which antenna is selected, which messages are loaded in the logger. At a multi-operator station that knowledge lives in several heads, and during the contest it moves from one head to another every few hours. If the move is rushed, details are lost. The new operator does not know that the amplifier was switched off, that the logger is set to a special exchange or that the previous operator worked a rare multiplier and has a note for it.
The consequences range from small to serious: a few minutes of rate lost while the new operator finds the right settings, a CQ on the wrong frequency, a QSO logged under the wrong operator, or a wrong exchange sent for an hour before anybody notices. The log keeps all of these mistakes, and they appear in the final result.
Plan the shifts in advance
A good handover starts with a good plan. Decide the shift schedule before the contest, write it down and share it. A written schedule should show who operates when, who is on standby and where the hours of rest are. Avoid very short shifts, which create too many handovers, and avoid shifts that are too long, because tired operators make errors. For most stations a block of two to four hours works well, though it depends on the team and the contest.
Overlap the shifts slightly. If the outgoing operator stays for five minutes next to the incoming one, the handover is relaxed and the questions can be asked. A hard stop with the chair empty for a minute is the worst case. For more on the way fatigue affects a team, see the articles on operator fatigue and breaks and fatigue and errors by hour.
A five-point handover routine
The routine should be short enough that people will really use it. Five points cover most situations.
- Where we are. The outgoing operator says the band, mode and frequency, whether the station is running or searching, and what the current rate is.
- What is special. Any antenna in use, a band that is closed, a station that is expected to call, a problem with the station that is being watched.
- Logger and clock. The incoming operator looks at the logger: the operator callsign or name, the exchange that is sent, the contest settings and the UTC clock.
- Multipliers and notes. The outgoing operator passes the list of needed multipliers or the bandmap marks, and any pending QSOs that were postponed.
- Confirmation. The incoming operator repeats the main points back, makes the first QSO and the outgoing operator checks that the line in the log is right.
Put the routine on a card next to the keyboard. When people are tired, they follow a list better than they remember one.
Operator identity in the log
Many loggers record which operator made each QSO. This matters for the statistics and, in some categories, for the rules about operators. If the logger asks for an operator callsign or name at the start of the shift, make it part of the routine. A QSO that is credited to the wrong operator may not change the score, but it will confuse the review of the rate by operator, and some contests ask for the list of operators in the header.
The article about the rate sheet by operator describes what you can learn from the numbers, and the one on the Cabrillo header shows how the OPERATORS line is written. Check them before the contest and decide how the team will fill the field.
Check the exchange you send
The most expensive handover mistake is a wrong exchange that is sent for hours. It can happen when one operator changes a setting, for example a zone for a portable operation or a power class, and the next operator does not know about it. It can also happen when the new operator uses a different set of function-key messages. The new operator should listen to a few of his own transmissions and compare them with what the rules require.
For this reason the first QSOs of a shift deserve extra attention. Read the first line of the log after the handover, and check the callsign, the exchange sent and the operator. If you also work with a second computer, check both. The article on logger defaults that send the wrong exchange explains why a small setting can have a long effect.
Keep the frequency and the rhythm
If the station is running, the frequency is an asset. Do not leave it empty during the handover, and do not let the incoming operator start a new search for a frequency in the first minutes. Let the outgoing operator keep calling CQ until the new operator is ready, or let the new operator start with a short CQ and take over the keyboard when comfortable. A clean handover on a good frequency can save several minutes of rate.
If the station is searching and pouncing, the handover is easier, but the same principle applies: the new operator should see the bandmap, the list of worked stations and the needed multipliers. Many loggers show these on the screen, and a short look is enough to orient. Explain anything that the screen does not show, for example a band that has just changed.
Special cases: breaks, guests and the night
Three situations deserve a few words of their own. The first is the break: when an operator takes a short rest, the station is often left on the same frequency with the logger running. If the break is part of the operating plan, say so in the notes, and check whether the rules count the time as off time. In some contests a break of a certain length counts against the operating time of a single operator, and in a team it may matter for the category. Read the rules, and see our article on off time and breaks.
The second is the guest operator, who may be skilled but does not know your station. Give a guest a short written introduction: the logger, the main messages, how to change band and where the notes are. Pair a guest with an experienced operator for the first hour, and check the first QSOs together.
The third is the night shift. Fatigue makes a routine more valuable, not less. At night, the incoming operator is often woken from sleep, and a clear card prevents the common mistakes: forgetting to check the clock, starting on the wrong antenna or sending a message from the previous contest. Make the card short and bright, and let the outgoing operator read the five points aloud if the incoming one is not fully awake.
Notes that travel with the shift
Use a written log of events next to the computer: a sheet, a whiteboard or a shared file. Every operator writes short notes: a band that opened, a problem with an antenna, a station that said it would be on another band, a callsign that was doubtful. The next operator reads the notes at the start of the shift and adds new ones at the end. Over a 48-hour contest these notes become a record of what happened that is much richer than the log alone.
After the contest, the notes help with the log review. A doubtful callsign with a note beside it is easy to check against a recording. An unusual drop in the rate can be explained by an entry such as an antenna fault. The article on the station change notebook shows a simple format, and the one on marking moments during the contest shows how to use time marks in the review.
After the contest: merge and review
If the team used more than one computer, the logs must be merged, and the handover details come back as a problem of identity and time: different clocks, different operator names and the same QSO on two machines. Check each computer’s clock before the contest, and agree on one format for operator names. The article on multi-op log merge errors explains the typical problems.
The review is a team activity as well. Look at the rate by operator, not to blame anyone but to find where the station was strongest. Check the QSOs around the handover times: do they show a gap, a wrong exchange or a callsign that looks different from those before and after? That is where the routine has to be improved for the next contest.
Related reading
The bottom line
A handover is a short routine with a big effect: where we are, what is special, logger and clock, notes and confirmation. Plan the shifts, overlap them slightly, write notes and look at the first QSOs after each change. The log of a team is only as clean as its weakest handover. For the questions about what a log check looks at, see the FAQ.
FAQ
How long should a handover take?
Two to five minutes is enough if the routine is fixed and the notes are written. Longer handovers cost rate.
Who should check the first QSOs after the change?
The outgoing operator, if still present, or the incoming operator, who reads the first log lines. Either way, someone must look.
Does the operator field in the logger matter?
It matters for statistics and, in some contests, for the header of the log. Agree on a format before the contest.
What if a shift change happens during a pileup?
Keep the pileup running and hand over the chair after the pileup, or let the incoming operator take over the keyboard while the outgoing one explains.
Do I need a paper checklist?
A card next to the keyboard helps tired operators follow the routine and costs nothing.



